Photos

Specifications

Physical Stats
Form Factor

* Proprietary

Dimensions

* 9.6" x 10" (24.4cm x 25.4cm)

Processor/Cache
CPU

* Dual 771-pin LGA Sockets
* Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
o Quad-Core Intel®
Xeon®Processor 5300 sequence (Clovertown processor) 90 watt or lower power
o Dual-Core Intel®
Xeon®Processor 5100 sequence (Woodcrest processor) 90 watt or lower power

System Bus

* 1333 / 1066 / 667 MHz system bus

System Memory
Memory Capacity

* Four 240-pin DIMM sockets
* Supports up to 16 GB 667 / 533MHz DDR2 ECC FB-DIMM memory
* Memory must be populated in pairs

Memory Type

* 667 / 533MHz FB-DIMM (Fully Buffered DIMM) ECC DDR2 SDRAM 72-bit, 240-pin gold-plated DIMMs

DIMM Sizes

* 256 MB, 512 MB, 1GB, 2GB, 4GB

Memory Voltage

* 1.8 V only

Error Detection

* Corrects single-bit errors
* Detects double-bit errors (using ECC memory)
* Supports Intel® x4 and x8 Single Device Data Correction (SDDC)

On-Board Devices
Chipset

* Intel® 5000V (Blackford VS) chipset
* MCH + ESB2

SATA

* Intel ESB2 SATA 3.0Gbps Controller
* RAID 0, 1, 5, 10 support (Windows)

Network Controllers

* Two Intel® (ESB2/Gilgal) 82563EB Dual-Port Gigabit Ethernet Controller
* Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output

Graphics

* XGI Volari™ Z7 16MB

Clock Generator

* ICS932S401EGLF

Super I/O

* Winbond 83627HG chip

Input / Output
Serial ATA

* Four Serial ATA ports
* Four SATA hard drives supported

IDE

* Single EIDE channel supports up to two UDMA IDE devices (IDE-M, IDE-S)
* Supports UDMA Mode 5, PIO Mode 4, and ATA/100

Floppy

* 1 Floppy controller; 1.44 MB

LAN

* 2x RJ45 LAN ports

USB

* 2x USB rear ports
* 1x USB internal headers for 2 ports
* Total 4 USB 2.0 Compliant / 1.1 Compliant

VGA

* 1x VGA Port

Keyboard / Mouse

* PS/2 keyboard and mouse ports

Serial Port / Header

* 1 Fast UART 16550 serial port
* 1 Fast UART 16550 serial header

Chassis ( Optimized for X7DVL-L )
1U Chassis

* CSE-811TQ-520
* CSE-811i-520
* CSE-512F-520
* CSE-512F-520L

Mid-Tower

* CSE-733TQ-645 (MCP-310-00010-01 air shroud required)
* CSE-733i-645

Important Chassis Notes

* To ensure system stability, a 420W (minimum) ATX power supply
[8-pin (+12V) and 24-pin are required]

Expansion Slots
PCI-Express

* 1 (x8) PCI-e slot

PCI

* 1x 32-bit 33MHz PCI (5 V) slots

System BIOS
BIOS Type

* 8Mb Flash EEPROM with Phoenix® BIOS

BIOS Features

* Plug and Play (PnP)
* SMBIOS 2.3
* DMI 2.3
* PCI 2.2
* ACPI 1.0
* USB Keyboard support
* Hardware BIOS Virus protection

Management
Software

* Super Doctor III
* Watch Dog
* NMI

Power Configurations

* ACPI Power Management
* Main Switch Override Mechanism
* Wake-On-Ring (WOR) header
* Wake-On-LAN (WOL) header
* Power-on mode for AC power recovery
* Internal / External modem remote ring-on

PC Health Monitoring
CPU

* Monitors for CPU Cores,+1.8V, +3.3V, +5V, ±12V, +3.3V Standby, +5V Standby, VBAT
* 4-Phase-switching voltage regulator

FAN

* Total of five 4-pin and 3-pin fan headers supporting up to 5 fans
* 5x fans with tachometer status monitoring
* Status monitor for speed control
* Status monitor for on/off control
* Support 3-pin fans (w/o speed control)
* Low noise fan speed control
* Pulse Width Modulated (PWM) fan connectors

Temperature

* Monitoring for CPU and chassis environment
* CPU thermal trip support
* Thermal Control for 5x fan connectors
* PSU I2C temperature sensing logic
* Thermal Monitor 2 (TM2) support

LED

* CPU / System Overheat LED
* Suspend-state indicator LED
* +5V Standby alert LED

Other Features

* Chassis intrusion detection
* Chassis intrusion header
* SDDC Support

Operating Environment / Compliance
RoHS

RoHS 5/6

* RoHS Compliant 5/6, Server Exemption

Environmental Spec.

* Operating Temperature: 10º to 35º C (50º to 95º F)
* Non-operating Temperature: -40º to 70º C (-40º to 158º F)
* Operating Relative Humidity: 8% to 90% (non-condensing)
* Non-operating Relative Humidity: 5 to 95% (non-condensing)