| Processor |
One
or two IntelŽ
XeonŽ processors with an 800MHz system bus. |
| System
Memory |
| Memory
Capacity |
Supports Registered ECC DIMMs that must be populated
in pairs.
| |
DDR
266/333 - Six DIMM sockets for up to 24
GB of DDR 266 or 12 GB of DDR 333 |
| |
DDR2
400 - Eight DIMM sockets for up to 16GB
of DDR2 400. |
|
| Memory
Type |
Registered
ECC DDR 266/333 SDRAM 72-bit, 184-pin gold-plated
DIMMs or registered ECC DDR2 400 72-bit, 240-pin
gold-plated DIMMs |
| Reliability
Features |
Corrects
single-bit errors and detect double-bit errors
(using ECC memory); supports x4 IntelŽ Single
Device Data Connection (SDDC), scrubbing, retry
on uncorrectable errors, memory mirroring, memory
sparing4 |
| Integrated
On-Board |
| Chipset |
IntelŽ
E7520 Chipset |
| IntelŽ
Server Network Connections |
One
IntelŽ
82541PI Gigabit Ethernet Controller and
One Marvell* Yukon* -EC 88E8050 PCI Express*
Gigabit Ethernet Controller, supporting teaming
and failover, 10BASE-T, 100BASE-TX, and 1000BASE-T,
RJ45 output. |
| Integrated
Management Controller |
National
Semiconductor* PC87431M Platform Instrumentation
ASIC |
| Graphics |
ATI*
RAGE* XL SVGA PCI video controller with 8 MB
of video memory |
| Integrated
Storage Support |
| Parallel
ATA |
Single-channel
ATA 100 (integrated single connector) supporting
two IDE devices |
| Serial
ATA |
Dual-channel
SATA 100 (two connectors on the server board)
supporting integrated mirroring and striping
(RAID 0 and 1) |
| Ultra320
SCSI |
E7520BD2V
and SE7520BD2VD2: One Ultra320/LVD channel via
either the LSI Logic* 53C1020 or LSI Logic 53C1020A
SCSI controller, with integrated mirroring and
striping (RAID 0 and 1), and support for modular
ROMB (IntelŽ RAID Controller SRCZCRX)6 |
| SE7520BD2SCSI
and SE7520BD2SCSID2: Two Ultra320/LVD channels
via the LSI Logic 53C1030 SCSI controller and
connected via two internal 68-pin-wide connectors;
maximum data transfer 320 MB/sec on each Ultra320/LVD
channel, with integrated mirroring and striping
(RAID 0 and 1), and support for modular ROMB
(IntelŽ RAID Controller SRCZCRX)6
|
| Input/Output |
| PCI |
Six
total slots6: one PCI Express x8,
one PCI Express x4 (physical connector is a
x8 slot), one PCI-X 133MHz, two PCI-X 100MHz,
one PCI 32-bit/33MHz 5V |
| IDE |
One
legacy IDE connector for support of up to two
IDE devices |
| USB |
Two
USB 2.0 ports2 (rear) and two USB
ports via internal headers for up to four USB
ports. SE7520BD2 and SE7520BD2SCSI have three
USB 2.0 ports on the rear and two USB ports
via internal headers. |
| Serial
Ports |
One
external DB9 serial port; one internal serial
port (which can become Emergency Management
Port if system-management card supports EMP) |
| Floppy
Controller |
1.44
MB and 2.88 MB, 3-mode support |
| Keyboard/Mouse |
Two
PS/2 ports, 8240A-compatible |
| IntelŽ
Server Management |
| Integrated
Management Type |
Onboard
Platform Instrumentation |
| Software
Support |
IntelŽ
Server Management family of software; upgradeable
via custom add-in card to support IntelŽ Management
Module. |
| IntelŽ
Management Module Support |
Professional
Edition, Advanced Edition |
| Supported
Standards |
IPMI,
DMI, CIM, SNMP, ICMB |
| Fully
Validated Operating Systems |
Microsoft
Windows Server* 2003 Enterprise Edition, Microsoft
Windows 2000 Advanced Server, Red Hat* Linux*
Enterprise 3.0, SUSE LINUX Enterprise Server
9, and Novell* NetWare* 6.5. |
| System
BIOS |
| Type |
4MB
Flash ROM with AMI* BIOS, Multiboot BBS (BIOS
Boot Specification). |
| Special
Features |
Plug
and Play, IDE drive auto-configure, SMBIOS 2.3,
ECC/Parity support, multilingual support, enabled
for IntelŽ One Boot Update for BIOS updates,
flashable, integrated BIOS setup utility. |
| Configuration
Utilities |
Server
Configuration Wizard for system setup of BIOS
utilities; Save and Restore System Configuration
Utility and initial IntelŽ Server Management
8 configuration. |
| Jumpers |
CMOS
clear, password clear, BIOS recovery |
| Front-Panel
Support |
Power
button, reset button, diagnostic interrupt (front-panel
NMI) button, system identify button, system
ID LED, status/fault LED, chassis-intrusion
switch and front-panel lockout; connection for
optional IntelŽ Local Control Panel7
for monitoring and control of the server from
the front panel. |
| Mechanical |
| Board
Style |
SSI
Entry E-Bay v3.0 and v3.5 |
| Board
Size |
12"
x 13" (305 mm x 269 mm) |
| Power
Requirements |
| +5V |
3.6A
maximum continuous current |
| +5V
Standby |
0.5A
maximum continuous current |
| +12V |
0.7A
maximum continuous current |
| +3.3V |
3.2A
maximum continuous current |
| -5V |
0A
maximum continuous current |
| -12V |
0A
maximum continuous current |
| Environment |
| Ambient
Temperature |
Operating
(system): 10°C to 35°C; non-operating/storage
(system): -40°C to +70°C ambient |
| Relative
Humidity |
Non-operating:
95%, non-condensing at 30°C |
Safety
and EMC Regulatory Compliance (Class A)
(EMC Regulatory Compliance is based on a board
configured in an Intel host system in which
Intel tested the board and found it compliant.) |
| Country
and District |
| Australia
and New Zealand |
AS/NZA
3548 Class A Emissions |
| Canada |
UL
60950 - CSA60950 |
| Europe |
EN55022
- Class A Emissions (CENELEC Europe), EN55024
Immunity (CENELEC Europe) |
| International |
CISPR
22 - Class A Emissions |
| Japan |
VCCI
Class A Emissions - Verify compliance only |
| Korea |
RRL
MIC Notice No. 1997-41 (EMC) and 1997-42 (EMI) |
| Russia |
GOST
R 29216-91 Class A Emissions, GOST R 50628-95
Immunity |
| Taiwan |
BSMI
CNS13438 Class A Emissions |
| United
States |
FCC/ICES-003
Verification to Class A Emissions |
